Add an Elegant Hanging Light the Easy Way

For the longest time, we’ve wanted some kind of light above the sink in our kitchen. We finally settled on a simple DIY solution to this problem using the IKEA Hemma cord set. The cord set comes with a long electrical wire that has a normal 2-prong plug on one end, and a light socket on the other. The light socket has a removable screw piece to allow you to attach a lamp shade. The screw piece holds the shade securely onto the light socket end of the cord. The cord itself is quite strong and can easily handle a glass shade hanging from it.

The cord set comes with an open eye hook, but it didn’t work in our situation because there was no stud in the ceiling where we wanted to hang the light. We ended up buying a hanging plant hook kit. We had to modify the hook slightly because the plastic wire hanger that came with the Hemma was too small to fit over the end of the planter hook.

To fix this, I simply cut the end off of the hook with a small hacksaw. The metal was very soft and this took only seconds.  If you don’t have a hacksaw, you could possibly use heavy duty wire cutters to cut the end off.

These hanging kits are designed to hold hanging planters which are pretty heavy and come with the parts to install on either a stud or directly into drywall.  The drywall anchor is a spring toggle bolt, which is capable of hanging a lot of weight. This is a bit overkill for this project, but it doesn’t hurt. For other projects, you may want to check out which kind of drywall anchor would be right for you. To install this toggle bolt, I used a half-inch spade drill bit to drill a hole in the ceiling large enough to accept the toggle bolt when it is folded.

Once the hole has been drilled, simply insert the toggle bolt and screw the hook until it is tight against the ceiling.

We planned to power the light using a power socket under the kitchen cabinets by the sink but we didn’t want the plug just hanging down from the ceiling for two reasons; 1) Because it is unsightly and 2) because the Hemma wire was several feet too long. What we decided to do was to run the wire inside our cabinets and leave the extra wire on top of the cabinet. To do this, we used a larger drill bit to drill a hole bottom shelf and the top of the cabinets as close to the back corner as possible.

A 1-inch spade drill bit which was just wide enough to handle the plug.

We threaded the wire through the holes and tied a knot just before the bottom hole leaving enough on the other side to reach the plug under the cabinets. This knot should prevent any extra wire from coming through the hole.

To keep the wire out of the way and tidy inside the cabinet, we used small nails to tack it to the back side of the cabinet facing. This also help rout the wire neatly around the inner shelves.

We got a shade from a local Habitat for Humanity ReStore for $2.00. These stores are great because they have a wide variety of random construction pieces and furniture for great prices and the money goes to help Habitat for Humanity. The particular share we got was a bit too big to fit on the screw part of the hemma, so I filed down some of the plastic on the hemma’s light socket to make some room. I was only able to thread a couple of threads on the socket with the screw piece, but that was plenty to hold the shade.

All in all, the IKEA Hemma proved to be a great solution for us. There are tons of really great examples out there using it as well. It allows you to be creative and still coming up with a professional look.  If you have used the Hemma for a DIY lighting project, we’d love to see what you did! Leave us a comment with info and a link.

 

 

Creating a Duct Tape Chair

I purchased a dome chair from a big box store last year and it didn’t hold up very well.  The chair part ripped and fell of the frame.  Since the frame was still left intact, I didn’t want to throw it away -so I reused it to make a new chair.  Using duct tape (the best duct tape of all – Nashua 357), I created a new frame for the chair.  This project was quick, cheap, and easy; it used less than $10 in materials and only an hour of my time.  The result is a chair that is much sturdier than the original I purchased. 

Read moreCreating a Duct Tape Chair

Large Floor Bookshelf Part 1

Start to Finish Banner

This is the first part in a two part series about how to design, build, and finish a simple woodworking project.  This part focuses on the design and build of the project.

Jessica and I tend to collect a lot of books.   I mean a LOT of books.  When one of those cheap 7ft tall particle board bookcases we had finally bit the dust, and fell on me, I decided we would only get solid wood bookcases from now on.  I also decided that it was probably best that the bookcase we get to replace the broken one be rather short, something that would fit just under the window in our living room. With the cost of solid wood bookcases being pretty high and nothing available suiting our needs exactly, I decided we should design and build one ourselves. Rather than trying to fit a new bookcase into our living room, why not design one that already fits?

Read moreLarge Floor Bookshelf Part 1

My First Ikea Purchase…Needed a Facelift

Ikea DrawersAdam and I had been in search for a drawer system for use in our office, and then there it was, the Ikea Alex.  Everything was right.  It was the perfect height.  It had plenty of long thin drawers, perfect for tool organization.  It even had wheels.  We excitedly perused our color options;  white, white, or white.  Hmm….

Our office is mostly wood tones and black, so white was just not working for our color palette.  At first we tried to find another option, but we just kept coming back to the Alex.  It had the barebones of exactly what we needed.  That’s when we decided to buy the Alex and give it a facelift.  Our plan was to paint it black and customize the drawer fronts.  This is how we did it.

Read moreMy First Ikea Purchase…Needed a Facelift